Simple Glue Bottle Holder

Keep two glue bottles upside down and ready to use. This simple holder uses four pieces of 3/4-inch plywood, wood glue and brad nails, with two top openings and matching shallow recesses below.

Woodworking · Beginner · 30 minutes, plus glue curing

Tools

  • Ruler or tape measure
  • Square and pencil
  • Saw for cutting plywood
  • Drill or drill press with 1-1/4-inch and 2-inch Forstner bits
  • Brad nailer
  • Sandpaper
  • Clamps and scrap backing board

Materials

  • 3/4-inch plywood

Hardware

  • Wood glue
  • 1-1/4 in brad nails
  • Sandpaper assortment

Cut list

  • Top panel — 1 × 8 in × 3 in × 3/4 in Plywood
  • Bottom panel — 1 × 8 in × 3 in × 3/4 in Plywood
  • Side spacers — 2 × 1-1/2 in × 3 in × 3/4 in Plywood

Diagrams

Glue bottle holder showing top and bottom hole layouts and an assembled front view with two side spacers. Top openings differ in diameter; matching bottom recesses are shallow.Glue bottle holder showing top and bottom hole layouts and an assembled front view with two side spacers. Top openings differ in diameter; matching bottom recesses are shallow.

Build steps

  1. Cut the parts

    • Cut the top, bottom and two side spacers from 3/4-inch plywood. The top and bottom are 8 x 3 inches; the spacers are 1-1/2 x 3 inches. Sand any rough edges.

  2. Drill the holes

    • Mark both panels 2 inches from each end and centred across the 3-inch width. • Drill through the top: a 1-1/4-inch hole on the left and a 2-inch hole on the right. • Drill two 2-inch-diameter recesses in the upper face of the bottom panel, each 1/8 inch deep. Clamp the panels securely and use a backing board for the through holes.

  3. Assemble

    • Stand the side spacers between the panels, flush with each end. Glue and brad-nail the bottom to the spacers, then attach the top the same way. Keep the corresponding holes aligned.

  4. Finish

    • Sand smooth and let the glue cure. Check that your bottles fit securely before use. Adjust hole sizes before assembly if your bottle caps differ.

Safety notes

  • Wear safety glasses, hearing protection, and appropriate respiratory protection when cutting, sanding, routing, or machining materials.
  • Read the entire project plan and confirm all measurements, material sizes, and tool setups before beginning any cuts or assembly.
  • Always follow manufacturer safety instructions and use proper safety equipment such as push sticks, guards, clamps, and stable work supports.
  • Never operate tools while fatigued, distracted, or under the influence, and seek supervision or assistance when using unfamiliar tools or techniques.
  • MakerMind provides informational project guidance only; users are responsible for safe tool operation, verifying measurements, and maintaining a safe workshop environment.

Common mistakes to avoid

  • Top holes and bottom recesses do not align

    Why it happens: The panels are marked from different reference edges.

    How to avoid: Mark both panels 2 inches from each end and 1-1/2 inches from either long edge. Keep the same orientation when assembling.

  • Bottom recesses drilled too deep

    Why it happens: The drill depth is not controlled or checked.

    How to avoid: Set a depth stop and test on scrap. Both bottom recesses are 2 inches in diameter and only 1/8 inch deep; do not drill through.

  • Bottle caps do not fit the openings

    Why it happens: Glue bottle caps and necks vary in size.

    How to avoid: Check your bottles before drilling. The top left hole is 1-1/4 inches and the right is 2 inches. Test the fit before assembly and adjust if needed while keeping the bottles securely supported.

  • Side spacers shift during nailing

    Why it happens: Wet glue lets the spacers slide out of position.

    How to avoid: Clamp the spacers flush with each end before nailing. Centre the brads in the spacer edges, keep hands clear of the nail path, and check that the top and bottom remain aligned.

Finishing suggestions

  • Sand smooth. Leave unfinished or add an optional clear finish for easier cleanup.

More woodworking and DIY plans